| Firestik antenna
mounting kits include the mount and coax |
| |
Jeep Wrangler 1997 forward - Hood Jam
This mini-kit was specifically designed for the 1997 and newer Jeep
Wranglers. The mounting bracket attaches to the front fender lip
under the vehicles hood (either left or right side). All of the stainless
steel mounting hardware (supplied)is hidden under the hood. The bracket
is 2" (51mm) wide by 3" (76mm) long.
The kit includes a stainless steel mount, 18 ft (5.5m) of professional
grade Fire-Flex coaxial cable. (MKJ4R) |
|
|
|
Single, Roof/Trunk Mount Mini-Kit
The mount in this mini-kit was exclusively designed right
here at Firestik to offer you a strong and stylish installation.
Unlike many of the similar style mounts on the market that use inferior
plastics and high resistance multi-part inserts, our mount has a
single chrome plated brass insert and is molded of 30% glass reinforced
nylon. It is the quality you deserve and have come to expect from
Firestik. The base diameter of the mount and the overall height is
only 2"
(51mm). With a simple 1/2" (13mm) hole, you can put this mount
on any flat horizontal surface. Because of the "very" low
profile, coax termination, this is the ideal set-up for roof mounts.
The underside space consumption is only 0.710" (18mm) so it
will work well under most headliners. We include a rubber gasket
to seal out water and a sturdy support washer too. (MKDM18R)
|
|
|
| |
Trunk
Mount System
The mount in this mini-kit is designed for trunk applications.
The mount bracket hooks over the rear lip of the trunk deck
and is tightened from underneath with two allen head screws.
There are no mounting holes! The bracket has two rubber
feet on the bottom to give additional support to the mount.
The coax connector (PL259) is included but must be soldered on the cable. (MK748R) |
|
|
|
Side body mount
If you are looking for a side mount with some style, than this is
the set up for you. This kit includes the molded side mount and
18 ft (5.5m) of professional grade Fire-Flex coaxial cable. If adding
a spring with a base diameter larger than 0.700", a split lock
washer is required between the mount and the spring to ensure proper
seating of the spring to the mount surface. For use with antennas up
to 4 feet long. (MKM2) |
|
|
|
Truck
bed rail mount & coax
- Single antenna system
Now you can install a CB or scanner antenna on the bed rail of
your pick-up without drilling holes in the exterior of the vehicle.
You get a quality stainless steel mount and 18 ft (5.5m) of professional
grade Fire-Flex coaxial cable (with our exclusive Fire-Ring connector)
all in one package! (MK294R) |
|
|
| |
Hood &
channel mount & coax
- Single antenna system
This kit is similar to our MK-174 kit with the added feature of
front to back angle correction. Many vehicles have a slope to the
hood and trunk channel and the fixed mount just won't work. Not
only will the antenna stud bracket swing a full 180 degrees, but
all of the holes needed for installing the mount are concealed.
You get a quality stainless steel mount and 18 ft (5.5m) of professional
grade Fire-Flex coaxial cable (with our exclusive Fire-Ring connector)
all in one package! (MK274R) |
|
|
|
Mirror
arm mount & coax - Dual antenna
system
This kit is the premium set-up for those planning to install dual
(co-phased) antennas on their vehicle. You get quality 3-way stainless
steel mounts and twin 18 ft (5.5m) professional grade coaxial cable
all in one package! And if that isn't enough, you save money to
boot.
(MK64A9A ) |
|
|
|
Mirror
arm mount & coax - Single Antenna
System
This kit is the premium set-up for those wanting a single antenna
system on their vehicle. You get our popular 3-way stainless steel
mount and 18 ft (5.5m) of professional grade coaxial cable all
in one package! And, because you buy it in a kit form, you save
money (MK64A8A ) |
|
|
| 
|
Door
Jam mount & coax - Single Antenna
System
This mount in this kit allows you utilize the inside edge of any
of the door jambs on your vehicle, regardless of the angle. The
antenna stud mounts to an adjustable swivel bracket to allow you
to keep the antenna vertical in spite of any left/right tilt of
the door jamb. The antenna stud bracket swivels a full 180 degrees
making the possible mounting applications many. You get a quality
stainless steel mount and 18 ft quality coax. (MK204R) |
|
|
|
Dodge truck - hood jam mount system
Dodge new body style truck mount. When the hood is open, the fender
bolt near the firewall is removed (right or left side) and
later reused to bolt the antenna bracket to the under-hood
fender lip. All mounting hardware is invisible unless the
hood is open. Additional stainless steel sheet metal screws
are supplied if additional strength is determined to be
needed. The bracket has a pre-determined bend and does not
interfere with the closing of the hood (MK184R) |
|
|
|
Hood & trunk
mount system
The mount in this mini-kit is designed for hood and trunk applications.
The stainless steel mount fastens to the inside channel of your
hood or trunk. There are no visible mounting holes. The included
mounting hardware (also stainless steel) is hidden inside the
hood or trunk channel. (MK174) |
|
|
|
Workman
trunk mount kit
The mount in this mini-kit is designed much like the Firestik version.
The bracket hooks over the rear lip of the trunk deck and is tightened
from underneath with two allen head screws. There are no mounting
holes! The actual mount sits flush on the body. Includes
18 feet of coax.
(WORK C-100) |
|
|
